Відео

looks super beautiful with all the decoration on it

Just got the plans for these, looking forward to building mine this weekend

What thickness of plywood are you using for the bodies of the tool holders (not the cleat, which I assume is ¾ ") - do you use ½" plywood or ¾"?

On the plans it has two holes for the rockers and both say rear but the picture only shows 1 hole? Any advice?

Oh man, you're going to need a set of real strong arms to help with those piles.

Awe he loves the house

Cooling pad for him too in that kennel ..m

Congratulations on your new home. Looking forward to upcoming videos as you make the new place, your place.

Awesome! You have some cool projects coming up. Can't wait!

beware the link for the plans leads to a malicious site

Great video and great help for making the table saw throat plate. I have to admit I'm not that good at making throat plates but this video is a BIG help, it also helps that I have the same Laguna table saw :)

I am gonna copy this! The entire ceiling!!! 😂😂. Quarter inch,,, one fourth is also correct, but makes you sound less knowledgeable in the eyes of a crusty old b*st*rd like me! 😂😂 Thanks for the idea!! Well done, VERY well explained (except for,, you know😂), and it looks good as well!

Are there still plans for this?

Awesome build and second GO AVS GO!!!!

I am currently about halfway done with this rocking horse and had a question for you or anyone else here who has done this project. I just attached all 4 legs and sat it down on the floor and it doesn’t quite sit flat on all 4 legs, kinda rocks back n forth just a bit if that makes sense. My question is would you recommend taking the time to sand it accordingly so it all sits flat or just try and make the adjustments when mounting it to the rocker support piece? Thanks

Great project! We have one of the bosch compound miter saws in the shop. Its a really good saw but I dont have much to compare it against. The festool looks awesome but then you need the festool Domino and Festool tracksaw and a Festool paml sander....

Looks good. I may need to adapt the length of the cart to my shop space though.

Glad to see you back! Tip when routing on narrow pieces: put one of your other pieces on each side of the working piece so that you have a wider and more stable base to run the router on. Also, you could use a couple pieces of scrap on either side of your work piece, and secure then to the router base as fences, creating a channel that your working piece fits nicely into, causing it not to wobble. Hope those tips made sense! Looking forward to more videos!

In the US in 2023 there were 1,600 fires due to lithium ion batteries in the US with 115 fatalities, could not find any fires related to home dust collection due to static discharge in any year. I am sure someone in the US is worried about static discharge with there PVC ducting all the while plugging in the EV car or ? into there home charging system.

Yeah what if the keyholes are horizontal?

Nice build. Just curious - why not knock out the lift template in the CNC?

How's the totes holding when it's too hot weather in the garage?

Where is the formula?

Hey I counted 2 90 degree fittings 😅

You asked me to......i would have done everything differently...except 1: the glue, titebond 3. And 2: finish sand with 220. In the end it seems you did a great job.

My favorite scrap wood cart on YT so far was the one with a middle section for full sheets (so they stand up straight and don't need to be "leafed" through) and bins for off-cuts and 1x/2x lumber on the sides.

Interesting, I use a hive system and bulbs, linked back to both hive and the Apple home app, and have had them for around three years. I have not seen any of these issues at all.

$560.00 for the router lift is insane

This is amazing 😊

Need a drawing, can you share them

Just what I was looking for. Great video. Short and to the point!

I’m interested in your vacuum system? I’m trying to set up my workshop now and I really need to have ideas on how to make my vacuum system work for me and my tools around the shop?

I can testify that this design works really well. Consolidates so much lumber, sheet goods, and off cuts into a small area that can be moved around as needed for wood access or other shop operations.

Wax paper for glue-ups. That’s freaking genius!

I like your idea of fabricating your cleats for the back of the tool holder. Thanks for providing the well edited video.

Rotary drill mentioned is a brace and uses an auger bit. Uses a two piece chuck with a spring to keep it together. Rachet back and forwards for tight spaces. Often used for mortice and tenons in upright rustic studs and beams, fences gates etc. Vertical boring was done with your chest against the round pad on the top that had a bearing in it. No carpenter or bridge builder in the past was ever without one. Cheers from Australia.

Nice sweet idea

Where did you get the circle jig for your bandsaw? Thanks for the video by the way.

Bought directions many months ago Decided to cut all pieces Like the idea of a folding table. Your directions do not show measurement details for circles as far as attachments to legs and top rail. Have you a more detailed plan that fills in the Measurements and leg placement on the circle pieces?

These plans are no longer available. How can I get them?

You have such a beautiful family ❤

Grounding/Earthing a PVC Dust Extraction System! Time to End the Nonsense!! - ua-cam.com/video/yA22kTtV4XI/v-deo.html

What hinges did you use?

Fabulous job! Well Done!

Love it. Love the Wedding photo in the background. ;) We live in North Salt Lake 👍

What a bout mitre cuts? Are you going to swap the throat plate out on your drop saw every time you make a mitre cut?

Thank you. I have a 2 year old granddaughter and this would be perfect since we have little storage space for it. Again, Thanks.

plans are a lower cost on Woodcraft

That was so simple and smart. Now I can hang a few items that's been in the garage. Thank you!

Thank you very much. It is going to help me very much in the pegboard I am making in India. Can you help with the measurements for the support you used to hang the pegboard on the wall? Thanks much.